Wireless Microphone Interference – Squelch It

Share Button
Wireless Microphone Interference – Squelch It

Keeping Noise Out And Letting In The Good Stuff  Photo provided by peterzen

Last week, I was called into a church for resolving a wireless microphone problem. Over the phone, it sounded like an easy fix. Once I got there, that’s when the real trouble started.

“If I can re-create the problem then I can fix the problem.”  Those are the words I have used throughout my life. Whether it was a computer problem, electrical problem, or audio problem, if I could re-create the problem, I could fix it. It comes down to this; when you can recreate the problem, you can analyze the components and track down the source of the problem. Find the source and you’re right around the corner from a solution.

Talking with the guy at the church, he explained they were having interference with one of the microphones. Please note, this church is very close to the interstate and a huge truck stop. CB interference was likely. I checked all of their wireless microphones for the frequency ranges they used. Everything was in the UHF (Ultra High frequency) range – nothing in which the CB radios should interfere.

Next, I took to verifying all wireless microphones were on different channels. I had expected if that was the case, two channels would be picking up the same microphone and not getting interference. It was only at this point I decide we should turn on all of the wireless microphones and their appropriate mixer channels. Having a paper chart of the wireless microphones and frequencies was a good place to start so I knew what I had in the room.

All the microphones were active for about twenty minutes with zero interference. Then, I walked up to the stage and knelt down by the receiver units and the house speakers started emitting a painful sound. I looked at the receiver units and one had the clip light flashing. I moved back and it stopped. I moved in again and the awful sound started again. So I squelched it.

Squelch

A definition of squelch is, according to the Merriam-Webster dictionary, “to completely suppress.” By suppressing or stopping a sound, you aren’t giving it any volume in your house speakers. Wireless receivers have the ability to squelch sound as well. Imagine a squelch circuit which acts much like a noise gate. If the signal level of the radio frequency is below a certain amount, the gate stays closed and nothing gets passed to the mixer channel. When the signal is strong enough, the signal is passed along. At this point, the squelch circuit is keeping background noise from being passed to your channel.

But what about interference? Is there a way to squelch that? In short, yes.

The folks at Audio-Technica describe it like this;

“Interference complicates the [squelch circuit] situation considerably. Interfering signals can trick the receiver into un-muting the audio output, especially when the wireless transmitter is turned off. One approach to this problem is to make the squelch point adjustable. Often a squelch setting can be found that will un-mute the receiver when the strong transmitter signal is received, but not when only the weaker interfering signal is present. Unfortunately, a high or “tight” squelch setting usually will also reduce the maximum range of the wireless system. This is because the transmitter must be relatively close in order to deliver the necessary strong signal to the receiver.”

On the back of your analog wireless microphones will be a small knob labeled “squelch.” Which begs the question…

How do I set the squelch?

Shure microphones give you a simple set of instructions;

  1. Turn the transmitter power off to eliminate the desired signal.
  2. Turn on all associated equipment in nearby locations to create the “worst-case” signal condition.
  3. Set the receiver volume control to minimum to avoid excessive noise in the sound system.
  4. Turn the receiver power on.
  5. Observe the RF and audio indicators on the receiver.
  6. If the indicators are showing a no-signal condition the squelch setting may be left as-is.
  7. If the indicators are showing a steady or intermittent signal-received condition increase the squelch control setting until a no-signal condition is indicated. Set the squelch control slightly past this point to provide a threshold margin.
  8. If the no-signal condition cannot be achieved even with high squelch settings it may be possible to find and eliminate the undesirable signal. Otherwise it may be necessary to select a different operating frequency.
  9. Turn the transmitter power on.
  10. Make sure that the receiver indicates a signal-received condition with the transmitter at normal operating distance.

The Take Away

There are a lot of benefits of using wireless microphones. At the same time, using wireless technology means you are introducing a whole new host of potential problems. The next time you have an interference issue with a wireless microphone, listen to what being emitting through that channel. If it’s the nastiest sound you’ve ever heard, then it’s likely a problem you can easily squelch.

Subscribe to our mailing list

Comments

  1. Matt G. says

    I have a similar problem with a Nady-4 UHF wireless microphone setup in which the squelch was adjusted to remove interference from a second Nady-4 receiver set at a different frequency (rack mounted next to each other) but I am still having problems with the audio from the transmitter being muted due to interference. One of the units is set to about 911 MHz and the other is operating at about 915 MHz. Any thoughts?

    • says

      Matt, can you set the frequencies farther apart? With that much room between then< i wouldn’t expect any issues. Have you tried the squelch on both?

      • Matt G. says

        Chris,
        The frequencies are set at the factory for the units so I cannot easily modify them. I have also set the squelch on both units, but I am not at maximum adjustment. The interesting thing is that the handheld mic. (on the 915 freq. unit) doesn’t mute as bad as the hands free setup (on the 911 freq. unit), but you can still tell that there is a bit of interference because of the volume changes at times not associated with movement of the microphone.

  2. Anonymous says

    Great article. I am facing the interference issue at my church and I have set my squelch to high but I still have problems. Do you have any suggestions. I have a mix of sennhieser and shure mics.

    • says

      Check that your different wireless frequencies between the mic’s aren’t right next to each other. Also, is it occasional interference is could it be they are too close to the monitors?

  3. Jim S. says

    Pardon the newbie question. I understand the use of squelch that you describe so well in the article. Thanks! However, in this case study, what exactly was causing the noise that needed to be squelched? Was the signal somehow disrupted by approaching the base unit?

    Thanks again for the great articles!

    Jim

Leave a Reply

Notify me of followup comments via e-mail. You can also subscribe without commenting.